5154A (AW-AlMg3,5 (A))

AlMg3,5 (AG3)

Aluminum for food using.

Mechanical characteristics : Properties :

 

Nominal chemical compound % (according to the standard EN 573-1):

 Si

 Fe 

 Cu

 Mn

 Mg 

 Cr 

 Zn 

Remarks

 Ti

Others

 Al

Each
Total
0,5
0,5
0,10
0,50
3,1-3,9
0,25

0,20

0,1-0,5 Mn+Cr

0,2

0,05

0,15

Reste

 

Specific mechanical characteristics:

 

Sheets (according to the standard EN 485-2) :

 State
Specified thickness
Rm (MPa)
Rp0,2 (MPa)
A %
Bending radius
Hardness HBS
More than
Until
mini
maxi
mini
maxi
A 50
A
180°
90°
F

³ 2,5

80,0

215

 -

-

-

-

-

-

-

-

 O/H111

0,2

0,5

1,5

3,0

6,0

12,5

0,5

1,5

3,0

6,0

12,5

50

215

215

215

215

215

215

275

275

275

275

275

275

85

85

85

85

85

85

12

13

15

17

18

 

 

 

 

 

 

16

0,5 t

0,5 t

1,0 t

 

 

 

 0,5 t

0,5 t

1,0 t

1,5 t

2,5 t

 

58

58

58

58

58

58

 H112

³ 6,0

12,5

40,0

12,5

40,0

80,0

220

215

215

 -

125

90

90

8

 

 

 

9

13

 -
 -

63

59

59

 H12

0,2

0,5

1,5

3,0

6,0

12,5

 0,5

1,5

3,0

6,0

12,5

40,0

 250

250

250

250

250

250

305

305

305

305

305

305

190

190

190

190

190

190

 -

3

4

5

6

7

 

 

 

 

 

 

6

-

75

75

75

75

75

75

H14

0,2

0,5

1,5

3,0

6,0

12,5

0,5

1,5

3,0

6,0

12,5

25,0

270

270

270

270

270

270

325

325

325

325

325

325

220

220

220

220

220

220

2

3

3

4

5

 

 

 

 

 

 

4

 -

81

81

81

81

81

81

H18

0,2

0,5

1,5

0,5

1,5

3,0

310

310

310

270

270

270

 -

1

1

1

-

-

-

94

94

94

H19

0,2

0,5

0,5

1,5

330

330

 -

285

285

-

1

1

-

-

-

100

100

H22/H32

0,2

0,5

1,5

3,0

6,0

12,5

0,5

1,5

3,0

6,0

12,5

40,0

250

250

250

250

250

250

305

305

305

305

305

305

180

180

180

180

180

180

5

6

7

8

10

 

 

 

 

 

 

9

1,5 t

1,5 t

2,0 t

 

 

 

0,5 t

1,0 t

2,0 t

2,5 t

4,0 t

 

74

74

74

74

74

74

H24/H34

0,2

0,5

1,5

3,0

6,0

12,5

0,5

1,5

3,0

6,0

12,5

25,0

270

270

270

270

270

270

325

325

325

325

325

325

200

200

200

200

200

200

 -

4

5

6

7

8

 

 

 

 

 

 

7

2,5 t

2,5 t

3,0 t

 

 

 

1,0 t

2,0 t

2,5 t

3,0 t

4,0 t

 

80

80

80

80

80

80

H26/H36

0,2

0,5

1,5

3,0

0,5

1,5

3,0

4,0

290

290

290

290

345

345

345

345

230

230

230

230

3

3

4

5

-

-

-

87

87

87

87

H28/H38

0,2

0,5

1,5

0,5

1,5

3,0

310

310

310

 -

250

250

205

-

3

3

3

-

-

-

93

93

93

Top of the page

Extruded bars (according to the standard EN 755-2) :

State
Sizes mm
Rm (MPa)
Rp0,2 (MPa)
A % mini
A50 % mini
Diam (D)
Size on flat or thickness (S)
mini
max
mini
max
F/H112
£ 200
£ 200
200
-
85
-
16
14
O/H111
£ 200
£ 200
200
275
85
-
18
16

Top of the page

Extruded tubes (according to the standard EN-755-2) :

State
Sizes mm

Thickness of wall

Rm (MPa)
Rp0,2 (MPa)
A % mini
A50 % mini
mini
max
mini
max
F/H112

£ 25

200

-

85

-

16

14

O/H111

£ 25

200

275

85

-

18

16

Top of the page

Extruded sections (according to the standard EN-755-2) :

State
Sizes mm

Thickness of wall

Rm (MPa)
Rp0,2 (MPa)
A % mini
A50 % mini
mini
max
mini
max
F/H112

£ 25

200

-

85

-

16

14

Top of the page

Drawn bars (according to the standard EN-754-2) :

State
Sizes mm
Rm (MPa)
Rp0,2 (MPa)
A % mini
A50 % mini
Diam
Flat
mini
max
mini
max
O/H111
£ 80
£ 60
200
260
85
-
16
14
H14/H24/H34
£ 25
-
260
320
200
-
5
4
H18/H28/H38
£ 10
-
310
-
240
-
3
2

Top of the page

Drawn tubes (according to the standard EN-754-2) :

State
Sizes mm

Thickness of wall

Rm (MPa)
Rp0,2 (MPa)
A % mini
A50 % mini
mini
max
mini
max
O/H111

£ 20

200

260

85

-

16

14

H14/H24/H34

£ 10

260

320

200

-

5

4

H18/H28/H38

£ 5

310

-

240

-

3

2

Top of the page

Wires according to the standard EN 1301-2 :

State
Diameter until and included
Rm (MPa)
Rp0,2 (MPa)

specific

A100 m % specific
mini
max
O
20
-
275
125
16

H14

18

280

330

270

3

H18
10
330
 -
320
2

H32

18

235

285

170

11

H34

15

265

315

230

8

H36

10

290

340

250

6

H38
10
 310
 -
  280
4

Top of the page

Properties (for information only):

 

Corrosion :

General corrosion index
Very good
Corrosion in industrial atmosphere
Very good
Corrosion in sea atmosphere
Very good
Corrosion in country atmosphere
Very good
Corrosion under stress
Good
Exfoliation  index
Very good
Intercrystalline corrosion
Good
Tapping index
Very good

Top of the page

Anodizing:

Bright anodizing
Satisfactory
Coloured anodizing
Good
Hard anodizing
Very good
Protecting anodizing
Very good

Top of the page

Strain, workability:

 
Annealing
Strain aging
Cold working
Good
Satisfactory
Deep stamping
Good
Satisfactory
Strain by tension
Good
Satisfactory
Embossing ability
Good
Satisfactory
Extrusion ability
Good
Good
Workability
Satisfactory
Good

Top of the page

Welding:

Welding by electron beam
Very good
Gas welding 
Satisfactory
Arc welding
Very good
Spot welding
Very good
Brazing
Not recommended
Soft brazing
Not recommended

Top of the page

Physical and elastic properties:

Elastic
Physical
E
G
n
Tsol
Tliq
Cp
a
r
rel
l
EC
MPa
MPa
-
°C
°C
J kg-1 K-1
µm m-1 K-1
kg m-3
nW m
W m-1 K-1
%IACS
 70500
26600
0,33
595
645
897
23,8
2680
54
129
32
Legend:
E 
Elastic modulus MPa
G 
Rigidity modulus MPa
 n
Poisson's ratio  
Tsol 
Solidification temperature °C
Tliq 
Melting temperature °C
Cp 
Specific heating J kg-1 K-1
a
Ratio of temperature expansion µm m-1 K-1
r
Density kg m-3
rel
Resistivity nW m
l 
Heat conductivity W m-1 K-1
EC 
Electrical conductivity %IACS

 

Top of the page