6082 (AW-AlSi1MgMn)

AlSi1MgMn (AGSM0,7)

Aluminum for food using.
Mechanical characteristics : Properties:

 

Nominal chemical compound % (according to the standard EN 573-1):

 Si

 Fe 

 Cu

 Mn

 Mg 

 Cr 

 Zn 

 Ti

Others

 Al
Each
Total
0,7-1,3
0,5
0,10
0,4-1,0
0,6-1,2
0,25

0,20
0,10

0,05

0,15
Reste

 

Specific mechanical characteristics:

 

Sheets (according to the standard EN 485-2) :
 State
Specified thickness (mm)
Rm (MPa)
Rp0,2 (MPa)
A % mini
Bending radius
Hardness HBS
More than
until
mini
maxi
mini
maxi
A 50
A
180°
90°
O

>0,4

1,5

3,0

6,0

12,5

1,5

3,0

6,0

12,5

25,0
-

150

150

150

150

155
-

85

85

85

85

 

14

16

18

17

 

 

 

 

 

16

1,0 e

1,0 e

 

 

 

0,5 e

1,0 e

1,0 e

2,0 e

 

40

40

40

40

40

T4

T 451

> 0,4

1,5

3,0

6,0

1,5

3,0

6,0

12,5

205

205

205

205
-

110

110

110

110
-
-

12

14

15

14

3,0 e

3,0 e

 

 

 

1,0 e

1,5 e

3,0 e

4,0 e

 

58

58

58

58
T451

12,5

40,0

40,0

80,0

205

205
-

110

110
-
-

13

12
-
-

58

58
T42

>0,4

1,5

3,0

6,0

12,5

40,0

1,5

3,0

6,0

12,5

40,0

80,0

205

205

205

205

205

205

-

95

95

95

95

95

95

-

12

14

15

14

 

 

 

 

 

 

13

142

 

 

-

 

 

1,5 e

2,0 e

3,0 e

4,0 e

 

 

57

57

57

57

57

57

T6

T651

T62

> 0,4

1,5

3,0

6,0

1,5

3,0

6,0

12,5

310

310

310

310
-

260

260

260

255
-
-

6

7

10

9

 

-

 

2,5 e

3,5 e

4,5 e

6,0 e

94

94

94

91

T651

T62

12,5

60,0

100,0

150,0

60,0

100,0

150,0

175,0

295

295

275

272

-

240

240

240

230

-

-

8

7

6

4

 

-

 

-

89

89

84

43

Top of the page

Sheets in relief (according to the standard EN 1386):

 State Specified thickness (mm) Rm (MPa) Rp0,2 (MPa) A % mini Bending radius min recommended at 90°
More than until mini maxi Mini Maxi A 50 A

O

1,2

1,5

3,0

6,0

1,5

3,0

6,0

20,0

-

-

-

-

150

150

150

150

-

-

-

-

85

85

85

85

6

8

10

12

-

-

-

12

2,0 t

2,0 t

2,0 t

-

T4

1,2

1,5

3,0

6,0

1,5

3,0

6,0

20,0

205

205

205

205

-

-

-

-

110

110

110

110

-

-

-

-

6

8

10

12

-

-

-

12

4,0 t

4,0 t

4,0 t

-
T6

1,2

1,5

3,0

6,0

1,5

3,0

6,0

20,0

310

310

310

310

-

-

-

-

260

260

260

260

-

-

-

-

2

3

4

6

-

-

-

6

-

-

-

-

T61

1,2

1,5

3,0

6,0

1,5

3,0

6,0

20,0

280

280

280

280

-

-

-

-

205

205

205

205

-

-

-

-

3

4

6

9

-

-

-

9

7,0 t

7,0 t

7,0 t

-

Top of the page

Extruded bars (according to the standard EN 755-2) :
State
Sizes (mm)
Rm ( MPa)
Rp0,2 (MPa)
A %
A50 %
Diam
Flat
mini
maxi
mini
maxi
mini
mini
O/H111

<200

<200

-
160

-
110

14

12
T4
<200
<200
205
-
110
-
14
12
T6

<20

20 à 150

150 à 200

200 à 250

<20

20 à 150

150 à 200

200 à 250

295

310

280

270
-

250

260

240

200
-

8

8

6

6

6

 

 

 

Top of the page

Extruded tubes(according to the standard EN-755-2):
State
Sizes mm

Thickness of wall

Rm (MPa)
Rp0,2 (MPa)
A % mini
A50 % mini
mini
max
mini
max
O/H111

£ 25

-

160

-

110

14

12

T4

£ 25

205

-

110

-

14

12

T6

£ 5

5<e£25

290

310

-

-

250

260

-

-

8

10

6

8

Top of the page

Extruded sections (according to the standard EN-755-2) :
State
Sizes mm

Thickness of wall

Rm (MPa)
Rp0,2 (MPa)
A % mini
A50 % mini
mini
max
mini
max

O/H111

Toutes

-

160

-

110

14

12

T4

£ 25

205

-

110

-

14

12

Open section

T5
£ 5

270

-

230

-
8
6

T6

£ 5

5<e£25

290

310

-

-

250

260

-

-

8

10

6

8

Hollow section

T5

£ 5

270

-

230

-

8

6

T6

£ 5

5<e£10

290

310

-

-

250

260

-

-

8

10

6

8

Top of the page

Drawn bars (according to the standard EN-754-2) :
State
Sizes (mm)
Rm (MPa)
Rp0,2 (MPa)
A %
A50 %
Diam
Plat
mini
maxi
mini
maxi
mini
mini
O/H111
<80
<80
-
160
  
110
15
13
T4
<80
<80
205
-
 110
-
14
12
T6
<80
<80
310
-
 255
-
10
9

Top of the page

Drawn tubes (according to the standard EN-754-2) :
State
Sizes mm

Thickness of wall

Rm (MPa)
Rp0,2 (MPa)
A % mini
A50 % mini
mini
max
mini
max
O/H111

£ 20

-

160

-

110

15

13

T4

£ 20

205

-

110

-

14

12

T6

£ 5

5<e£ 20

310

310

-

-

255

240

-

-

8

10

7

9

Top of the page

Wires according to the standard EN 1301-2:
State
Diameter until and included
Rm (MPa)
Rp0,2 (MPa)

specific

A100 m % specific
mini
max

H13

£ 18

165

225

130

4

T39

³ 6

310

-

-

-

T39

< 6

360

-

-

-
T4
£ 20
205
 -
135
 13

T6

£ 20

300

-

270

10

T89

< 6

340

-

-

-

Top of the page

Properties (for information only):

 

Corrosion :
General corrosion index
Good
Corrosion in industrial atmosphere
Good
Corrosion in sea atmosphere
Good
Corrosion in country atmosphere
Very good
Corrosion under stress
Good
Exfoliation  index
Good
Intercrystalline corrosion
Good
Tapping index
Good

Top of the page

Anodizing:
Bright anodizing
Satisfactory
Coloured anodizing
Good
Hard anodizing
Good
Protecting anodizing
Very good

Top of the page

Strain, workability:
 
Recuit
T5
Cold working
Good
Acceptable
Deep stamping
Good
Acceptable
Strain by tension
Good
Déconseillé
Embossing ability
Good
Déconseillé
Extrusion ability
Good
Good
Workability
Déconseillé
Good

Top of the page

Welding:
Welding by electron beam
Good
Gas welding 
Good
Arc welding
Very good
Spot welding
Good
Brazing
Good
Soft brazing
Good

Top of the page

Physical and elastic properties:

State
Elastic
Physical
E
G
n
Tsol
Tliq
Cp
a
r
rel
l
EC
MPa
MPa
-
°C
°C
J kg-1 K-1
µm m-1 K-1
kg m-3
nW m
W m-1 K-1
%IACS
O
70000
26400
0.33
575
650
894
23.1
2710
31
216
55.5
T4
70000
26400
0.33
575
650
894
23.1
2710
41
167
42
T6
70000
26400
0.33
575
650
894
23.1
2710
39
172
44
Legend:
E 
 Elastic modulus MPa
G 
 Rigidity modulus MPa
 n
 Poisson's ratio  
Tsol 
 Solidification temperature °C
Tliq 
 Melting temperature °C
Cp 
 Specific heating J kg-1 K-1
a
 Ratio of temperature expansion µm m-1 K-1
r
 Density kg m-3
rel
 Resistivity nW m
l 
 Heat conductivity W m-1 K-1
EC 
 Electrical conductivity %IACS

 

Top of the page