Cu-HCP (CW024A)

 

Copper electrolytically or thermically refined that has gone through a deoxidation treatment with phosporus. The result is a phosphorus content from 0,013 to 0,050 %.

The residual phosphorus has the effect to decrease the electrical conductivity but it makes that copper insensitive to reducing atmospheres. So that grade applies to mechanical usings and is perfectly weldable with no limitation.

General engineering usings that do not require the highest conductivity. There is no oxygen, so no embrittlement.

It is the most often found as "thin" products such as sheets, tubes, strips.

 

Chemical compound %
Agent
Cu
Bi
O
P
Pb
Others
Mass-volume g/cm3
total
not included
Mini:

99,90

-

-

0,015

-

-

-

8,9

Maxi:

-

-

-

0,040

-

-

 

 

Mechanical properties of plates, sheets and coils for general usings (EN1652) :
State
Thickness
Tensile strength Rm N/mm²
Conventional elastic limit at 0,2Rp0,2 N/mm² .
Stretching
Hardness HV
From
to
min.
max.
A50mm ep < or = 2,5
A ep > 2,5
min.
max.

R200

more than 5

200

250

(max. 100)

-

42

-

-

H040

-

-

-

-

 -

40

65

R220

0,2

5

220

260

(max 140)

33

42

-

-

H040

0,2

5

-

-

-

-

-

40

65

R240

0,2

15

240

300

(min. 180)

8

15

-

-

H065

0,2

15

-

-

-

-

-

65

95

R290

0,2

15

290

360

(min. 250)

4

6

-

-

H090

0,2

15

-

-

-

-

-

90

110

R360

0,2

2

360

-

(min. 320)

2

-

-

-

H110

0,2

2

-

-

-

-

-

110

-

 

Mechanical properties of bars for general usings (EN 12163) :
State
Implementation
Diameter or size/flats mm
Tensile strength Rm N/mm² min.
Conventional elastic limit at 0,2Rp0,2 N/mm²
Stretching
Hardness
from
more than
until
A100mm % min.
A11,3 % min.
A % min.
HB min.
HB max.
HV min.
HV max.

M

 

2

-

80

-

-

-

-

-

-

 -

-

-

 R2002

 

 2

 -

 80

200

 (80)

 25

 30

 35

 -

 -

 -

 -

H0352

 

2

-

80

-

-

-

-

-

35

65

35

65

R250

 

2

-

10

250

(220)

8

10

12

-

-

-

-

R250

 

-

10

30

250

(210)

-

-

15

-

-

-

-

R230

 

-

30

80

230

(190)

-

-

18

-

-

-

-

H065

 

2

-

80

-

-

-

-

-

65

90

70

95

R300

 

2

-

20

300

(280)

5

6

8

-

-

-

-

R280

 

-

20

40

280

(260)

-

-

10

-

-

-

-

H085

 

2

-

40

-

-

-

-

-

85

110

90

115

R260

 

-

40

80

260

(230)

-

-

12

-

-

-

-

H075

 

-

40

80

-

-

-

-

-

75

100

80

105

R350

 

2

-

10

350

(330)

(3)

(4)

5

-

-

-

-

H100

 

2

-

10

-

-

-

-

-

100

-

110

-

2 Traité pour mise en solution

 

Mechanical properties of wires (EN 12166) :
State
Diameter
Tensile strength Rm N/mm˛
Conventional elastic limit at 0,2Rp0,2 N/mm²
Stretching
Hardness HV
from
more than
until
min.
Max.
A100mm % min.
A11,3 % min.
A % min.
min.
max.

R200

1,5

-

20,0

200

270

(60)

33

37

40-

-

-

H040

1,5

-

20,0

-

-

-

-

-

-

40

70

R270

1,0

-

8,0

270

-

(250)

10

12

-

-

-

H065

1,0

-

8,0

-

-

-

-

-

-

65

90

R250

-

8,0

20,0

250

-

(230)

-

-

15

-

-

H065

-

8,0

20,0

-

-

-

-

-

-

65

90

R330

1,0

-

8,0

330

-

(290)

(4)

7

-

-

-

H090

1,0

-

8,0

-

-

-

-

-

-

90

105

R300

-

8,0

15,0

300

-

(250)

-

-

10

-

-

H090

-

8,0

15,0

-

-

-

-

-

-

90

105

R400

1,0

-

8,0

400

-

(380)

-

-

-

-

-

H105

1,0

-

8,0

-

-

-

-

-

-

105

-

R350

-

8,0

12,0

350

-

(320)

-

-

-

-

-

H105

-

8,0

12,0

-

-

-

-

-

-

105

-

 

Mechanical properties of sections and rectangular bars (EN 12167):
State
Sizes
Tensile strength Rm N/mm² min.
Conventional elastic limit at 0,2Rp0,2 N/mm²
Stretching A %
Hardness
Section
Retangular bars thickness mm
> at
< or =
HB min.
HV min

M

All

 All

 

 

 

 

 

R280

-

-

6

280

(220)

(10)

-

-

H085

-

-

6

-

-

-

85

90

R240

-

6

60

240

(180)

(18)

-

-

H065

-

6

60

-

-

-

65

70